Te c hnical ManualRevision D: 04.18.08FSP 42/44/46 Flight Strip Printer
Figure 3a - FSP , Side View4A. Cutter AssemblyB. Optical DetectorC. Timing BeltD. Drive Pulley (2)E. TransformerF. Print Head Release LeverABCDEFNOTE:
5Figure 3b - FSP , Cover OpenA. Print Head Release LeverB. Logic BoardC. LCD Control BoardABCNOTE:LOGIC BOARD CONFIGURATIONS MAYVARY DEPENDING ON THE
Figure 4 - FSP , Rear View6A. AC Power ConnectorB. Fuse Holder (2amp,SB)C. Input SlotD. Interface Connector (Serial)E . Locking MechanismF. ON/OFF Swi
4.0 InstallationThe FSP is designed to be mounted on a counter top or shelf.However, prior to site and installation, the printer should be powered upa
FEED DIRECTIONFigure 7 - Flight Strip loadingYou may now install the printer in its permanent location. Adequate room should beprovided behind the pri
5.0 Standard ConfigurationThe FSP is factory configured for specific customer requirementsusing an enhanced FGL package. Printing resolution is 300 do
The chart below lists the present menu topics. These topics are subject to change.TEST TICKET TYPE? The FSP allows one of four different test tickets
MINI/MICRO?Defines the type of printer.MINI Is for a printer with a Cutter Assembly (factory default)MICRO Is for a printer without a Cutter AssemblyP
SPECIAL HEAD?Is used when a special paper path size is installed (2.125”, 2.5”, 2.7”...)Here are the following choices:PATH TYPE?Defines the number of
INC CUT2 COUNT?Same as INC CUT1 COUNT? but effects path #2 on a dual path printer.(Does not apply)DEC CUT2 COUNT?Same as DEC CUT1 COUNT? but effects p
BOCA SYSTEMS, INC.©2008 Boca Systems, Inc. All rights reserved.Under the copyright laws, this manual may not be copied, in whole or in part, withoutth
FLASH ACK MODE? Enables or disables an ACK being sent back to the host after a flash operation. Yourchoices areYES (Enabled) or NO (Disabled). NO is f
155.1 THIS SECTION HAS BEEN REMOVED This page has been left blank intentionally
Flash erase operation incompleteError No. DescriptionReadyPaperJam1ON OFF2 Flash Vpp problemOFFOFFDataOut ofpaper3456789101112131415OFFON OFFOFFFlash
6.0 Interface PinoutsSerial PinoutsRS232 (Standard)Pin Function2Printer Transmit3Printer Receive7Ground5,20 DTR (Printer Ready)4,22 RTS (+5Vdc)Typical
7.0 Thermal Paper - Theory & SpecificationThe print head’s life expectancy is composed of both a mechanical and an electrical component. Both ofth
8.0 Maintenance and AdjustmentsYour ticket printer is solidly constructed and has been designed for high volume use. Itrequires minimal care to prov
8.1.5.5 Ticket Load SwitchThe ticket load switch should be positioned such that the printer automatically activatesthe stepper motor at the proper tim
8.1.6 THERMAL PRINT HEADThe print head should be cleaned periodically to prevent debris from building up on theprint element. The required cleaning in
Figure 9a - Print Head removalFigure 9b - Print Head removalAdjustment set screws24Remove these two unmarked screws toreplace print head.FigureFigureF
8.2 Cutter Assembly8.4 General CleaningThe interior of the printer should be cleaned whenever there is a visible accumulationof dust. Use a small vacu
Table of Contents Page1.0 Introduction 12.0 Unpacking the Printer 23.0 A tour of your printer 34.0 Installation 74.1 Loading Flight Strips 75.0 Standa
9.0 PARTS LIST ITEM Part Numbers Description1423182 CABINET, FSP2 423182CV COVER, FSP3 423111FSP PRINT CAGE, FSP4 421366FSP PAPER GUIDE, FSP (LOWER)5
10.0 Troubleshooting GuideThis is a simplified troubleshooting guide listing some of the typical problems. It is not intendedto provide technical deta
287. POOR PRINT OUT(light print out)a. Make sure the print head/cam lock assembly if fully locked in the closed position.b. Consult“Thermal Print Head
Table of Figures and Appendices PageFigure 1 Packaging 2Figure 2a Control Panel and LCD 3Figure 2b Flight Strip Printer(FSP) 3Figure 2c Cabinet Lock M
FCC NOTICENOTE: The equipment has been tested and found to comply with the limits for a classA digital device, pursuant to part 15 of the FCC rules. T
WARRANTY INFORMATIONPRINTERS - BOCA warrants each printer to be free of defects for a period of one yearfrom the date of shipment when subject to norm
1.0 IntroductionThe BOCA Flight Strip Printer, (FSP) is a direct thermal ticket printer with an integratedcutting mechanism designed for air traffic c
2.0 Unpacking the PrinterThe printer is shipped in a ruggedized container. Please save packing material forfuture use. Remove the printer (see figure
3.0 A Tour of Your PrinterFigure 2b - Flight Strip Printer (FSP)3Output Slot(Hopper MountingHoles)Figure 2a - Control Paneland LCDFigure 2c - Cabinet
Comments to this Manuals